How To Mount A Scope On A Remington 700?

The Remington 700 has been a versatile rifle with a legacy ranging for more than half a century. It still makes the first choice for most for its robust build quality that lasts it for years. However, the best part that makes it so special is its accuracy at long range.

But as you might already know, accuracy at long range requires more than a good rifle. You need a perfect scope alignment, for that you must know how to mount a scope on a Remington 700.

Let’s dive deep to picture the idea of scope mounting in general and how it’s done with Remington 700 models.

Why Should You Care About Scope Mounting

Mounting a scope on your rifle means enabling it to shoot from a distance impossible to target with bare eyes. Although guns usually have an iron sight of their own, that doesn’t work for precise long range shooting. Therefore, you must put a scope on the rail to acquire higher efficiency, especially for competitive sports and hunting.

Why Should You Care About Scope Mounting

Certainly, you have to know how to mount the scope to make the best out of it. Whether you’re using a Night Vision Scope or a regular one, mounting it properly is utterly important. Use only the best quality tools while mounting a scope, especially the ones that help you align it with the rifle.

Tools You’ll Need To Mount A Scope On A Remington 700

Mounting a sight of any kind to your rifle requires both preciseness and attention to detail. Therefore, you’ll need a few tools to successfully mount the scope on your Remington 700 as follows:

  • The right scope (depending on the game)
  • A scope base
  • The rifle base
  • A tightener
  • Barrel leveler
  • 2 bubble levels
  • Lapping Bar
  • Optic leveler
  • A gun-oiled rag
  • Target practice area

How To Mount A Scope On A Remington 700

Mounting a scope on your rifle is certainly comparable to a fine art with a high level of perfection. One little misalignment may get you a really disappointing result, especially when it’s a long range rifle like the Remington 700 SA. So, here are the essential tips and how to mount a scope on a Remington 700:

How To Mount A Scope On A Remington 700

1. Choosing the Right Scope and Base

Source: https://warnescopemounts.com/picatinny-vs-weaver-style-bases/

First off, you must get the right base after getting your scope, where your purpose decides which scope to get. For the scope base, though, you want to be picky because the Remington 700 has an ejection port with recoil. Therefore, you should go with a 2-piece picatinny rail instead of a one piece.

If you have a 60-minute type of scope with a standard 20-minute base, you’re getting a total of 80 minute MOA there. With another 20 on the rings, you can get a total of 100 minutes from a 60-minute scope. You must zero the scope while keeping that calculation in mind.

2. Use Leveling Kits and a Base

Your job of mounting rifle scope to a Remington 700 starts with a mounting base. It will hold the rifle tight and firm as well as level with fine height tuning options. First, put the rifle on the base, and put a bubble level on the barrel, another on the handle. Level the gun accordingly and then move on to the rifle scope installation stages.

Use Leveling Kits and a Base

Start with mounting the scope plug screws, and use the right size Allen screw threads to tighten firmly. And be sure if it’s a permanent threadlocker or a removable threadlocker; use detachable scope rail mounts for removable ones. Use a torque wrench to tighten the bases, starting with the rear base. There are detachable ring mounts available in the market as well.

3. Aligning the Scope Right

To align the scope perianal to the muzzle, you have to take both the vertical and horizontal position into account. Sometimes, scopes come 90° angled, you want to have your elevation scope turret on the top. Windage might go to the right if there’s no parallax adjustment knob there. Most of the manufacturers put their logo as their reference point to put that on the opposite of the ejection port.

4. Tighten the Rings Properly

Source: https://warnescopemounts.com/is-lapping-needed/

Once you have your base ready, go ahead and mount the ring base on the rail and align that correctly. And for the parallel alignment, use a Lapping Bar to fine tune the ring so that they don’t have any misalignment. If you have your scope rings aligned, remove the bar and double check by putting bubble levels on both rings. Use the leveler your scope mounts to make sure it’s also aligned to the barrel.

5. Keep It in Your Natural Position

Since you’ll be looking through the scope for long periods, you must have it in your comfort zone. Some people do the mistake of concetrating only on the vertical adjustment, leaving the eye relief behind. Don’t do that. Put your scope on the ring and pull the scope towards you at your natural eye relief. Make sure you’re not needing to bend forward to get relief. Remember, do this once you have your scope and ring base in place. You can also mark the eye relief stage of the scope at this point for future reference.

Keep It in Your Natural Position

6. Go Up With Bigger Scopes

Now, if you’re using a bigger scope like above 50 mm or more, use a medium to high base. It’s difficult to use a lower base and have good clearance underneath at the same time. Use the medium height scope base and make sure the scope objective area doesn’t touch the barrel. Otherwise, you’ll damage your scope, or it may have a bad impact on the targeting from the recoil. Having the clearance will help you shoot more accurately, and avoid damaging the scope as well.

7. Get the Maximum Eye Relief

Eye relief is a major thing to think about when it comes to shooting without straining your eyes. Use a ring with the lowest height so that you don’t have to lift your head from the cheek pad. However, if you’re using a bigger scope with a bigger objective, follow the previous stage mentioned above. A few times of practicing with the gun, the scope, and the cheek pad will make you fluent.

8. Mounting the Scope on the Rifle

Now for the final part of mounting a scope onto your Remington 700, check if you have everything in place, aligned. Put the scope on the open ring, align it with the elevation turret facing up, then put the upper scope rings. Tighten them counterwise in an alternating pattern, but don’t tighten one all the way in, keep it loose.

Mounting the Scope on the Rifle

Pull or push the scope a little until you have them on your eye relief point. Now, get 2 bubble levels and put one on the base, one on the barrel, then keep on fastening. Make sure both the bubbles are centered properly while tightening. It’s important for a bolt action rifle with medium height rings that give you a big target area.

9. Zero the Scope on the Remington 700

Source: https://www.gunsamerica.com/digest/optics-buying-guide-properly-zero-scope/

Once you have the scope tightened all the way, it’s time to zero the scope. Zeroing the scope depends on how far your target is, and you’ll need a target, a rangefinder, and a marker. Sight your gun at your target in the center, shoot, and adjust the reticle elevation and windage until you hit the bulls eye.

Be sure to keep track of your distance with the rangefinder and use the same distance for the real game. Use the adjustment turrets, divide the distance between 0-500 yards and 500-1000 yards, and another for short, like 0-300 yards. And don’t forget about proper eye relief nonetheless during the process.

Safety Tips When Mounting A Scope On Remington 700

When you’re working with a gun, you want to take the utmost safety precautions in order to stay away from danger. There’s no exception while mounting a scope on your Remington 700. It’s for your safety, alongside the rifle itself. Here are some safety rules to maintain during mounting a scope to any rifle:

Safety Tips When Mounting A Scope On Remington 700

Don’t Forget the User Manuals

Proper scope mounting on your Remington shouldn’t be a guesswork, instead of a planned and documented way. Before you start the mounting process, be sure to understand how things in the job work. For example, not all models of scope mounts go the same way and there are rules regarding rifle scopes.

Empty the Chamber First

Before you start mounting the scope or doing anything in particular with your gun, empty the rifle in prior. You never want to work on your rifle while it’s steel loaded because that might cause a major accident. Simply slide the magazine first, or empty the chamber as you’re working on a Remington 700.

Clean the Mounting Area

There could be dust, gunpowder, or other debris on the mounting place from the field. You must clean any unwanted residue from there before you start mounting your scope on the rifle. Take a clean microfiber rag, dip it into a little gun oil without overdoing it, and wipe the area before starting the process.

Be Careful With the Base

The scope rail can be a major thing to pay attention to as you’re working on Remington bolt-action rifles. If you don’t use the right kind of rail on it, the ejected cartridge may hit the base. Therefore, you must go with a 2-piece picatinny scope base instead of EGW Remington weaver, which can keep you secure.

Test Before Shooting for Real

Don’t be overconfident and never rely completely on the mounted scope you’ve done. Before you go for the sport or hunting, be sure to test the scope in the field. Go to a practice range where it’s safe to make mistakes and test if the scope is doing its job well. Understanding scopes and zeroing them also goes into this phase.

Conclusion

The Remington 700 rifle can give you the most satisfying experience, regardless of whether you’re hunting or into competitive shooting. Now that you know how to mount a scope on a Remington 700, it’s necessary to take safety precautions wisely. That’s because mounting a scope for long range shooting has its tool to the processes.

And regardless to say, when you’re doing it with a Remington 700, it’s really important you make it right. You make a tiny misalignment, the bullet will travel to a wrong destination. Lastly, don’t forget about your comfort, get the right eye relief distance, and follow the scope mounting tips above.

Scroll to Top